Welcome to AmebaPro2’s Documentation!

documentation list

• Realtek AmebaPro2 application note
  • Building Environment
    • Setting up GCC Building Environment
    • Log UART Settings
  • SDK Architecture
    • Component
    • Project
    • Doc and tools
    • Binary files
    • SDK and lib version
  • GCC Makefile
    • Adding files in CMake project
    • Creating a new application example
    • How to use example source code
  • Image Tool
    • Introduction
    • Download Environment Setup
    • Image Download
    • Command line image tool for NOR flash
    • Command line image tool for NAND flash
  • Using JTAG/SWD to debug
    • SWD connection
    • Software installation
    • Setup environment
  • Multimedia Framework Architecture
    • Architecture
    • MM_Module Type and Module Parameter
    • Using the MMF example
    • AV SYNC
  • Memory Layout
    • Programming Space
    • Data Space
    • Extension Memory Space
    • SRAM Retention
  • Flash Layout
    • NOR Flash Layout overview
    • NAND Flash Layout overview
    • NAND Flash
    • NOR Flash
  • OTA
    • OTA Operation Flow for NOR Flash
    • OTA Operation Flow for NAND Flash
    • OTA Checksum Mechanism
    • Boot Process Flow
    • Upgraded Partition
    • Firmware Image Output
    • Implement OTA over Wi-Fi
    • Verify Signature after OTA
  • Power Save
    • Overview
    • Deep Sleep Mode
    • Standby Mode
    • Sleep Mode
    • Set AON GPIO pull control before power save mode
    • Set PON GPIO pull control before standby
    • Get Wake Reason
  • System API
    • System reset
    • Get boot select
    • JTAG/SWD disable
    • MPU read only section protect
    • Get DDR type & size
    • R/W otp logical map
    • Write otp to disable log uart
  • File System
    • FATFS File System
  • Audio optimization
    • Audio setting
    • Audio ASP algorithm
    • Audio test tool
  • NN
    • NN module
    • Model Zoo
    • NN model preparation (Acuity)
    • NN memory evaluation
    • Using the NN MMF example with VIPNN module
  • ISP
    • Sensor Driver
    • Image Quality
    • OSD2
    • ISP Control API
    • Privacy Mask
    • External Image Processing
    • Meta Data
    • IQ Driver Guide
    • IQ Tuning Guide
  • Bluetooth
    • BT Example
    • BLE Security
    • BLE Coexistence
  • System Resource Evaluation
    • Memory Section
    • Memory Size
    • Code Size
    • CPU Utilization
  • USB
    • UVC
    • USB CDC
    • USB DFU
    • USB PoE and Wi-Fi Network Connection Detection
  • Wi-Fi
    • Wi-Fi Data Structures
    • Wi-Fi APIs
    • Fast Connection
    • WPS APIs
    • Wi-Fi event callback function
    • Auto Reconnection
    • Multiple AP with specified ssid or mesh selection
    • Wifi Channel plan setting
    • Power by Rate and Power Limit Introduction
    • Wifi Adaptivity
    • Wifi disconnect events:
    • Modify the WIFI TX power method:
    • Wifi build MP user guide:
  • Peripheral
    • Flash spic QPI or QSPI setting
    • Aon watchdog
    • One-time Programmable (OTP)
  • Log System
    • Log redirection
    • Fault message redirection
• Realtek AmebaPro2 HW design Guide
  • Introduction & Design Goals
    • Overview
    • Target Audience
    • Hardware Design Philosophy
    • Design Flow Overview
    • Reference Materials
  • Schematic Guidelines
    • Reset, Boot & Firmware Upload Signals
    • Power & Regulation
    • Interfaces
  • PCB Layout Guidelines
    • PCB stack-up and impedance information
    • VIN-Sensor
    • USB
    • SPI flash
    • SD card
    • Decouple capacitors